banner



SPEED CODE 5 PROGRAMMER

THE SPEED CODE 5 PROGRAMMER DOES:
1.   INCREASE YOUR TORQUE and SPEED;
2.   RE-PROGRAMS THE CONTROLLERS FIELD MAP TO MATCH YOUR MOTOR;

Stock controllers are turned down by Club Car™, and DOES NOT allow the full 250 amps that the controller is capable; They are also not programmed for the full speed that the motors are capable of achieving. This is where the Speed Code 5 matches the controller to your MOTORS FIELD MAP and gives you more SPEED and TORQUE.

Returns / Refunds accepted for 14 DAYS after purchase. To receive a refund you must download the stock Club Car™ SPEED CODE 3 program into your controller, and it must be saved into programmer memory (last program downloaded is stored in memory) if stock program is not in memory, there will be no refund.

USING ZELLE
BANK TRANSFER

NO tax & NO shipping charges

Information Needed:

1. Zelle Bank Transfer
$150.00 TO: Bank@gaminde.net
2. Which Code 5, 6652 or 6662:
3. Your Shipping Address:
4. Your Email Address:
5. Your Phone Number:


BEFORE ORDERING, YOU NEED TO KNOW TWO THINGS

1.   WHICH MOTOR YOU HAVE !      ! Motors Pictured Here !
2.   DO THE CARTS SERIAL NUMBERS MATCH THE   GREEN SERIAL NUMBERS BELOW ?

THE CODE 5 PROGRAMMER WORKS ON IQ CARTS! SERIAL NUMBERS STARTING WITH:  NQ, AQ, PQ, CE, FD, HD, And PE.

THE CODE 5 DOES NOT WORK WITH SERIAL NUMBERS STARTING WITH:  TEMPO AN, BH, BN, BQ, BX, BV, BU, BT, BY, BZ,PH, PJ, PD, JE and JF.


SPEED CODE 5 WITH MCOR CHECK

The Speed Code 5 Programmer comes with MCOR / THROTTLE CHECK! This polls the controller to make sure the controller is seeing full throttle from the pedal assembly, the controller will only output full speed if the input it is given is a full throttle input. After programming, using the Speed Code 5 Programmer. This unit now checks for 95% or greater throttle. The Speed Code 5 Programmer polls the controller via serial communication and reports that the controller is seeing 95% or greater throttle. Controllers known to work with the Speed Code 5 Programmers are 1510-5250, 1510-5201, 1510-5251 and the 1510A versions of the same controllers. Speed Code 5 Programs are motor dependent This allows the controller and motor to be matched for better performance.

CAUTION: SPEED MAGNETS CAN BE DANGEROUS' REMOVING ALL CONTROLLER SAETY LIMITS!

SPEED CODE 5 PROGRAMMER™
Speed Code 5 Programmer

SPEED CODE 5 VS SPEED MAGNET

1.     SPEED CODE 5 TOP SPEEDS ARE EQUAL TO A 500 AMP REPLACEMENT CONTROLLER.
2.     SPEED CODE 5 DRIVEN SPEED IS 22 - 24 MPH SPEED MAGNET'S DRIVEN SPEED IS 19 - 20 MPH.
3.     SPEED CODE 5 GIVES YOU 20% MORE TORQUE AND SPEED OVER A SPEED MAGNET!
4.     SPEED CODE 5 INCREASES TORQUE, A SPEED MAGNET GIVES YOU NO ADDITIONAL TORQUE!
5.     SPEED CODE 5 HAS CONTROLLER / MOTOR RPM / SPEED LIMITS (FOR YOUR SAFETY) UNLIKE MAGNETS!
6.     SPEED CODE 5 CREATES NO ADDITIONAL STRESSES ON YOUR MOTOR OR CONTROLLER!
7.     SPEED CODE 5 PROGRAMS ARE CREATED SPECIFICALLY FOR YOUR MOTOR TO ENSURE MOTOR LIFE!
8.     SPEED CODE 5 CAN NOW BE ORDERED WITH SPEED LIMITS ADJUSTED TO YOUR SPECIFIC NEEDS!
9.     SPEED CODE 5 CAN BE INSTALLED FROM ANY SPEED CODE - CODES 1,2,3 or 4 TO SPEED CODE 5!
10.   SPEED CODE 5 PROGRAMMER CAN BE USED AN INFINITE NUMBER OF TIMES ON (ONE) CART!
11.   SPEED CODE 5 DOES NOT SHORTEN BATTERY LIFE OR RUNTIME!

SPEED CODE 5 OPTIONS

   6.6.5.2    High Output, STOCK AMD Black Motor, with MCOR check 
   6.6.6.2    High Output, STOCK GE Gray Motor,     with MCOR check 

ALL SPEED MOTORS MUST BE RUN IN TORQUE MODE ! !

The Speed Code 5 unit gives you at least 20% more Torque over stock code 4 settings;

Speeds are 3 to 4 mph faster than Club Cars™ Speed Code 4 setting (stock carts with no lift and stock tires are running 22 to 24 mph on flat ground). Most people are averaging 22+mph. Test Cart is a 2006 Club Car Precedent™ with a 6" lift, 22" Tires, Stock 1510-5201 Curtis™ controller, Stock AMD 3.2 HP motor and one year old batteries. Speed Code 5 speeds 26 to 27 mph. Remember, not all carts will achieve these top speeds; there are many variables including mcor, batteries, wires, motor condition, tires and many others. Refunds are available if you follow the refund policy below.



AMD MOTOR (black with the top hat style speed sensor) shows the most gains reaching speeds of 26-27 MPH. GE MOTOR (grey with the flat style speed sensor) have top speeds of 25-26 MPH

PROGRAMMING PROBLEMS


! This unit will work for one cart / controller only! it reads the controllers serial number then saves it into memory, also saving the last program downloaded.

Returns / Refunds accepted for 14 DAYS after purchase.

To receive a refund you must download the stock Club Car™ SPEED CODE 3 program into your controller, and it must be saved into programmer memory as stated above; (last program downloaded is stored in memory) if stock program is not in memory, there will be no refund.






Clicky







YOUR IP ADDRESS - 52.14.100.101